U2xAI
…

Lead Engineer

RTX (Raytheon) · Aerospace & Defense

  • IN-KA-BENGALURU-NORTHGATE ~ Sy No 2/2 Venkatala Village ~ SY NO 2/2 VENKATALA VILLAGE, Yelahanka Hobli
  • Hybrid
  • Posted today
  • Apply by 26 Nov
  • Core Engineering
Apply on RTX (Raytheon)(opens the employer’s site in a new tab)Create resume for this job

About the job

Date Posted:

2026-10-26

Country:

India

Location:

IN-KA-BENGALURU-NORTHGATE ~ Sy No 2/2 Venkatala Village ~ SY NO 2/2 VENKATALA VILLAGE, Yelahanka Hobli

Position Role Type:

Hybrid

Overview:

Responsible for capturing design architecture, electrical schematics, operational diagrams, and detailed technical documentation, including written and verbal descriptions, to ensure electrical designs meet defined requirements and specifications. Must perform electrical testing and should possess strong knowledge on using test equipment, troubleshooting, debugging, and issue resolution throughout the product development lifecycle.

Development and preparation of test articles, test fixtures, wire harnesses, and representative loads required for design verification, qualification, validation, and production activities as required.

Key Responsibilities & Qualifications

Bachelor’s degree in Electronics/Electrical Engineering.
Demonstrated working knowledge of Analog, Digital, and Mixed-Signal circuit design and analysis.
Perform component selection and evaluation of alternate components for circuit modules, including technical trade-off analysis based on performance, cost, availability, reliability, and lifecycle.
Develop and implement practical solutions to electrical and electronic design challenges with guidance from senior engineers where required.
Perform conceptual studies, design calculations, and technical feasibility assessments to support product development.
Perform circuit simulation and analysis using SPICE-based circuit simulators and appropriate device models.
Capture and review electrical schematics and provide PCB layout engineers with component placement, routing, grounding, and power-distribution recommendations.
Apply strong analytical and problem-solving skills to investigate and resolve electrical design and hardware issues.
Prepare and maintain design documentation, test procedures, verification procedures, and cable/harness diagrams.
Perform board bring-up, hardware debugging, and board-level verification testing.
Set up electrical test environments and demonstrate hands-on experience using laboratory equipment such as programmable power supplies, function generators, digital multimeters (DMMs), digital storage oscilloscopes (DSOs), and electronic loads.
Apply Design for Manufacturing (DFM), Design for Cost (DFC), Design for Quality (DFQ), and Design for Certification (DFC) principles during the design and development process.
Support design reviews, verification activities, qualification testing, and troubleshooting throughout the product development lifecycle.
Demonstrate good verbal and written communication, teamwork, collaboration, and interpersonal skills.

Preferred Technical Experience & Core Competencies

4-6 years of experience in the design and development of complex Analog, Digital, and Mixed-Signal electronic systems.
Experience in requirements capture, architecture diagram, worst-case analysis, design documentation.
Experience in working with interfaces like I2C, SPI, SRAM, CAN, ARINC 429, ARINC 664, EBI interface, 10/100/1000 Ethernet, UART and RS422/R485.
Experience in performing design analysis, testing, debugging, and troubleshooting of Analog, Digital, Mixed-Signal, and Power circuits.
Working Knowledge in signal integrity analysis and timing analysis.
Experience in schematic capture using Cadence OrCAD or equivalent schematic design tools.
Experience in circuit simulation and analysis tools, such as LTspice, PSpice, or equivalent platforms.
Experience in working with cross-functional engineering teams.
Hands-on experience with IHS, silicon expert, electrical component lifecycle and obsolescence management, including identification, evaluation, qualification, and implementation of alternate/replacement components.
Working Knowledge of DO-160 and DO-254 aerospace standards and their application to electrical/electronic product development.

Good to have:

Knowledge of Siemens Teamcenter or equivalent Product Lifecycle Management (PLM) tools.
Hands-on with SVN or other version-control/repository management systems.
Knowledge of Aerospace standards and products.
Knowledge in DO-160 and/or MIL-STD environmental qualification and testing.
Knowledge in software tools that will be used for De-bugging Microcontrollers/microprocessors during hardware testing, debugging, and validation.

WE ARE REDEFINING AEROSPACE.

Some of our competitive benefits package includes:

Transportation facility.
Meal coupons
Group Term Life Insurance.
Group Health Insurance.
Group Personal Accident Insurance.
Entitled for 18 days of vacation and 12 days of sick leave annually.
Employee scholar program
Work life balance
Car lease program
National Pension Scheme
LTA
Fuel & Maintenance /Driver wages
Meal vouchers
And more!

Nothing matters more to Collins Aerospace than our strong ethical and safety commitments. As such, all India positions require a background check, which may include a drug screen.

At Collins, the paths we pave together lead to limitless possibility. And the bonds we form – with our customers and with each other -- propel us all higher, again and again.

Apply now and be part of the team that’s redefining aerospace, every day

RTX adheres to the principles of equal employment. All qualified applications will be given careful consideration without regard to ethnicity, color, religion, gender, sexual orientation or identity, national origin, age, disability, protected veteran status or any other characteristic protected by law.

Privacy Policy and Terms:

Click on this link to read the Policy and Terms

Apply on RTX (Raytheon)(opens the employer’s site in a new tab)